How To Remove The Ejector Of

Refer to paragraph 19 for cleaning of receiver group.

36. Inspection a. Inspect the trigger for burs and wear (fig. 49). Inspect the half-cock position notch and full<ock notch of hammer for cracks, chips or wear. Make certain the hammer strut is not bent or cracked.

b. Inspect the sear for worn or chipped tips or w\irn lugs.

c. Inspect the sear spring for bmken leaves, cracks and tension.

d. Inspect disconnector for burs and wear.

e. Inspect the grip safety for burs, wear and cracks on the tip which engages the trigger.

f. Inspect the pin portion and lug of safety for wear and damage.

g. Inspect the helical compression spring (fig. 50) for cracks and tension.

h. Inspect the mainspring cap pin, detent plunger, and straight'headed pin for burs, wear or damage.

i. Inspect for bent or worn mainspring housing pin and spring pin.

j. Inspect slide stop, slide stop plunger and safety plunger for burs, wear or damage, k. Inspect magazine catch and magazine catch lock for bun* and wear. Check magazine catch spring for tension and damage.

I. Inspect helical compression spring (housing) for burs on mating surfaces and lanyard loop for being bent, worn or damaged.

m. Inspect grips for cracks and worn checkering.

n. Inspect the receiver housing (fig. 48) for wear or burs in the slide mating grooves. Inspect the receiver for deformation. Check to see that the plunger tube, ejector, ejector pin, and grip screw bushings are not burred or worn. Check the mainspring housing mating grooves in the receiver for burs. Check slide stop notch for oversize or wear. 37- Repair a. Remove burs fn>m slide mating surfaces of receiver housing and mainspring housing mating surfaces, using a fine stone.

b. Replace slide stop plunger and safety plunger, and ejector if worn or damaged. Replace plunger tube using plunger tube staking tool. Replace all bushings that have been removed from receiver housing, using bushing staking tool.

C. Remove bun» from trigger, replace if worn or damaged.

d. Replace hammer if cracked, chipped or worn.

e. Replace hammer strut if bent, cracked, worn or damaged.

f. Replace sear if lugs are worn and tips are worn or chipped.

g. Replace sear spring if leaves are broken or cracked, or tension is weak.

h. Remove bun from disconnector, rcplacc if worn or damaged.

i. Remove burs from grip safety, replace it cracked or worn on tip. j. Replace safety if worn or damaged.

k. Replace the helical compression spring (housing), if damaged or tension is weak. I* Remove burs from mainspring cap pin, detent plunger, and straight headed pin. Replace, if worn or damaged.

m. Rcplacc mainspring housing pin and spring pin if bent or worn, n. Remove burs fmm slide stop, slide stop plunger and safety plunger Replace, if worn or damaged.

o. Remove burs from magazine catch and magazine catch lock. Rcplace if worn. Replace magazine catch spring if damaged or tension is wrak.

p. Remove burs from the mating surfaces and mainspring housing. Rcplacc lanyard loop if bent or damaged.

q. Replace grips if broken or if checkering is worn. 38. Assembly Refer to figures 26 thru 32 for assembly of receiver group

IXX>TIC*

IXX>TIC*

REMOVF MAINSPRING HOUSING PiN

REMOVF MAINSPRING HOUSING PiN

wjnspring mousing assevbi.v wjnspring mousing assevbi.v

WJNS°RINQ HOJSJNG

REMOVE MAINSPRING HOUSING ASSEMBLY

Figure 3H. Duawemblyfossembl* of receiver group. (2 of J I)

HMiMgn Tnur

INSTALL MAINSPRING HOUSING PIN. @

Figure 3H. Duawemblyfossembl* of receiver group. (2 of J I)

RELEASE HAMMER AND POSiHON HAMMER ¿ft STRUT INTO MAINSPRING HOUSING ASSEMBLY

POSIT ON

INSTALL AND POSH ON SAFETY

INSTALL AND POSH ON SAFETY

COCK HAMMFR PRIOR TO INSTALLING SAFETY

HAMMER STRUT

HAMMER STRUT

MMMSPRING HOUSING ASSEV31Y

MMMSPRING HOUSING ASSEV31Y

DROP HAMMER STRUT AND INSTALL GRIP SAFETY

tigurc 59 Disassembly/assembly of receiver group 0 of iJ)

PARTIALLY INSTALL MAINSPRING HOUSING ffi

ASSEMBLY TO HOLD SEAR SPRING IN POSIHON w

CiB 7-2

HAMMER OMITTL3 FC« Cl AB TV

HAMMER STRUT

DISCONNECT

SFAF SPRN9

RFAR VCV/ SHOWNO

locATicfv er söR sffllRC

HAMMER STRUT,

REMOVE/INSTALL HAMMER STRUT PIN. ^ SEPARATE'CONNECT HAMMER STRUT AND HAMMER. Q

Figure 40. Di5üsseiTiMy<2ssembfy of receiver group. (4 of Jf.) GB J 5-1

INSTALL HAMMER AND HAMMER PIN

HAMME«

Figure 4f. Disaw*mWyas$eml>fy of receiver gnmp (5 of I ¡) GB

REMOVBINSTALL STRAIGHT HEADED PIN. ©

1911 Mainspring Cap Pin

SEPARATE/CONNECT DETENT PLUNGER. HELICAL ggk COMPRESSION SPRING AND MAINSPRING CAP PIN.

Figure 40. Di5üsseiTiMy<2ssembfy of receiver group. (4 of Jf.) GB J 5-1

DEPRESS SPWING |

REMOVE.'! N STALL MAINSPRING, CAP PIN. HELICAL COMPRESSION SPRING AND DETENT PLUNGER

SEPARATE/CONNECT DETENT PLUNGER. HELICAL ggk COMPRESSION SPRING AND MAINSPRING CAP PIN.

REMOVE/INSTALL LANYARD LOOP SPRING PIN.

DEPRESS SPWING |

REMOVBINSTALL STRAIGHT HEADED PIN. ©

REMOVE.'! N STALL MAINSPRING, CAP PIN. HELICAL COMPRESSION SPRING AND DETENT PLUNGER

HOUSING

SP&.NÜ pin

LOOP'

REMOVE SEAR SPRING

Figure 4 2

P9s Cutaway

igger disco nne'

igger disco nne'

CUTAWAY VIEW SHOWING LOCATION OF SFAR AND DISCONNECTOR

SEAR

DSCONECTOR

SE PARATE.'CONNECT SE AH AND DISCONNECTOR

IHiGOFR

DiECJM'JFC-C«

IHiGOFR

DiECJM'JFC-C«

REMOVE/INSTALL SEAR AND DISCONNECTOR Q

REMOVE/INSTALL SEAR AND DISCONNECTOR Q

UNLOCK/LOCK CATCH GROUP

REMOVE/INSTALL MAGAZINE CATCH GROUP Figure 43. D/su.s.s«-mW>/«smnWy of receiver group. (7 »f /J)

POSITIONING CATCH GROUP

Gil 9-1

REMOVE SEAR SPRING

Figure 4 2

SEPARATE.'CONNFCT I ANYARO LOOP ©

NOTE REMOTE TIN IHLW ROM!

left installing. head o; pin SMCX.LÜ aF ON l£ft soe.

NOTE REMOTE TIN IHLW ROM!

left installing. head o; pin SMCX.LÜ aF ON l£ft soe.

REMOVE/INSTALL SEAR P>N JXuzssembIy/aj5£mhl> of receiver group (6 of il)

REMOVE GRIP SAFETY V

REMOVE/INSTALL TRIGGER

SEPARATE/CONNECT MAGAZINE CATCH lOCK AND MAGAZINE CATCH SPRING

^FFTY r-vurvGCP

HE MOVE,'INSTALL

NC^: /«LIME MAGAZINE CATCH JXK LUG W.TH MAGAZINE CÄICH

tljrh cux<w3f cqr

MCJBp FOR RFMOTtWL

m/oa7inf catch sp** no

MAGAZINE CATCH LOCK

SEPARATE/CONNECT MAGAZINE CATCH lOCK AND MAGAZINE CATCH SPRING

^FFTY r-vurvGCP

SPRING

rs, ptonqer

SLIDE S>TOD I

safety plöngeh

REMOVE/INSTALL TRIGGER

HE MOVE,'INSTALL

COMPRESSION SPRING AND SAFETY PLUNGER

F<gu>? 44, Disarm blj/ajjímbfo of receiver group. <8 of If.)

screw

REMOVE/INSTALL PLASTIC GRIPS

REMOVE/INSTALL GRIP SCREWS.

UNSEA1ING PLUNGER TlJBF INSTALL/STAKE PLUNGER TUBE ON RECEIVER Q

Figure 45. DisiuwmMj/tfsscwW? <■/ rectw<.*r grrn*J>- <9 J') C?H KM

screw

REMOVE/INSTALL PLASTIC GRIPS

REMOVE/INSTALL GRIP SCREWS.

REMOVE .INSTALL EJECTOR P'N
M1911 Screw Bushing Staking Tool

VCTf GRIP SCREW BUSHINGS WILL W RE REMOVEO FROV RFC£lvE» UNI FS3 THREADS ARE STRIP3FO 0*

REMOVE GRIP SCREW BUSHINGS.

of receiver group. (10 of U)

REMOVE PLUNGER TUBE

EJECXfl

How Remove The Ejector Cal

REMOVE,'INSTALL

ejector. Figure

REMOVE PLUNGER TUBE

EJECXfl ejtc~jfl »IN

REMOVE,'INSTALL

ejector. Figure

Was this article helpful?

0 0

Post a comment