Storage Or Shipment

(9) Apply the following marking on each fiberboard container 10) Place a quantity of fiberboard containers into a cleated plywood box. A plywood box made in accordance with PPP-B-601 or PPP-B-621 may be used. (11) Strap the plywood box with 5 8 wide flat steel strapping. (12) Serial numbers are required and shall be listed on the packing list. The following marking shall be omitted from the outside of exterior shipping container 1005 01-118-2640 Pistol, Semiautomatic, 9mm, M9 b. Marking. Apply...

Maintenance Procedures

92f Mos Training

In order to reduce the space required for the initial setup portion of the maintenance procedures, the following data is standard for all initial setups a. Materials parts - includes only items applicable to the procedure. b. Tools and special tools includes only the standard tool set applicable to the procedure. c. Personnel required includes the following designated joint service descriptions that are applicable to all intermediate direct support maintenance...

Quarterly Schedule

If the pistol has not been used for 90 days, perform PMCS in the operator's manual ARMY TM 9-1005-317-10, NAVY SW 370-AA0PI G1G 9mm, AIR FORCE TO 11W3-3-5-1, MARINE CORPS TM 1005A-10 1, COAST GUARD COMDTINST M8370.6 . If you see rust on a pistol, the PMCS will be done immediately. 2 7. UNIT PREVENTIVE MAINTENANCE CHECKS AND SERVICES. a. General. The PMCS procedures are contained in table 2-2. They are arranged in logical sequence requiring a minimum amount of time and effort on...

Caution

Beretta 9mm Cutaway

If solid film lubricant comes in contact with any moving or internal part, clean part with dry cleaning solvent. 3. Apply solid film lubricant to all external surfaces showing wear. Allow to dry a minimum ot 12 hours before using weapon. 1. Grasp the slide with the bottom facing up. With the other hand, grasp the barrel assembly with the locking block facing up. 2. Insert muzzle of the barrel assembly into the forward open end of the slide. At the same time, lower the rear of the barrel...

Section V Unit Maintenance Procedures

Caliber Handgun Revolver Beretta

When a pistol is received at unit maintenance, it must be inspected and if any d ficiences are found, they should be repaired or noted tagged for repair at intermediate direct support maintenance next authorized repair level. a. Unit maintenance is limited to replacement of the pistol grips, minor hardware and reversing the magazine catch assembly. Coast Guard users are not authorized to reverse the magazine catch assembly. b. Initial Setup. In order to reduce the space required for the initial...

Warning

Pct Small Pistol

Use care when removing recoil spring and spring guide. Because of the amount of compression, assembly will be released under spring tension and could cause possible injury to personnel, or become damaged or lost. 5. Slightly compress recoil spring and spring guide, while at the same time lifting and removing recoil spring and spring guide. Allow the recoil spring to expand slowly. 6. Separate recoil spring from spring guide. 7. Push in on locking block plunger while pushing barrel forward...

Section I Repair Parts Special Tools And Support Equipment

For authorized common tools and equipment refer to the Modified Tabte of Organization and Equipment MTOE applicable to your unit. illustrated qn page 65 of this manual. illustrated qn page 65 of this manual. 2 2. SPECIAL TOOLS AND SUPPORT EQUIPMENT There are no special tools lor this item. There is no Test. Measurement and Diagnostic Equipment TMOE for this item.

Beretta 92 Firing Pin Spring Replacement

Beretta Firing Pin Hole

Rotate the slide with sights down. Carefully seat the firing pin block spring 1 into the recess hole 2 . Insert the firing pin block 3 into the firing pin block cutout. 14. With the forefinger, push in on the firing pin block 1 . Place the slide on its side and with a 3 32 inch punch, lightJy tap the firing pin block spring pin in until slightly below flush. If safety does not rotate freely between safe and fire positions, check right safety lever spring pins for correct installation. When...

Section Iv Troubleshooting

This section contains troubleshooting information for locating and correcting most of the operating troubles which may develop in the M9 pistol. Each malfunction for a part, assembly, or subassembly is followed by a list of tests or inspections which will help you to determine corrective actions to take. You should perform the tests inspections and corrective actions in the sequence shown Dn pages 12 through 18. The Symptom Index is for page referencing only. b. This manual cannot list all...

92 Army Pistol Disassembly

When applying pressure to the center coil area of trigger spring, use care to prevent ejection of trigger spring as it could become lost or cause possible injury to personnel. 12. With needle nose pliers, grasp the trigger spring 1 in the center coil area with the straight leg of the spring forward and the bent leg facing to the rear. Lower the trigger spring into the trigger spring cutout, ensuring that the bent leg of the trigger spring is resting on top of the trigger bar post. With a...

Beretta 92 Extractor

Feed Ramp 9mm Barretta

Before performing any of the troubleshooting procedures, make sure the pistol is clear unloaded. Do not keep live ammunition near work maintenance area. In this table, evacuate to intermediate direct support also means evacuate to the next higher level of maintenance. 1. Ammunition does not 2. Cartridge does not 3. Failure to 4. Failure to 5. Failure to 6. Hammer does not cock with safety in the fire 7. Hammer does not decock with safety in the safe 8. Slide does not lock fully 9. Slide does...

Pin Trigger P 226

Tomcat Trigger Bar Spring

Downward oressure must be maintained on the lanyard loop to overcome the main spring pressure. A 1 8 inch punch should be used to aline the lanyard loop spring pin hole with the hole in the receiver. This will allow proper atinement of the lanyard loop spring pin during installation. Ensure hammer is in the down or forward position. 9. Install the lanyard loop 9 into the main spring cavity 18 with the cutout forward. Rotate the receiver 1 and rest the lanyard loop 9 on a soft support. Compress...

Trigger Bar Spring

Disassembly Latch Release Button

To prevent loss of disassembly button and spring, be sure to release button pressure slowly after the removal of the disassembly latch lever. 1. Push in on the disassembly latch button 1 and rotate the disassembly latch lever 2 upward until contacting the slide rail. While maintaining firm pressure on the disassembly latch button 1 , pull out, and rotate upward to remove the disassembly latch lever 2 . 2. Remove the disassembly latch button 1 and spring 2 . When removing each pistol grip, the...

How To Dismantle A 9mm Handgun

9mm Pistol Dismantle

Make certain weapon is clear and there are no obstructions in the barrel or chamber. Equipment Condition Pistol, Field Stripped When removing each pistol grip, the Jockwashers may remain seated or come loose. Be careful not to lose them. To remove the pistol grips, remove grip screws 1 and lockwashers 2 . Insert the forefinger into the magazine weti and gently iift up on the pistol grip 3 . Repeat the procedure to remove the other pistol grip. To remove the pistol grips, remove grip screws 1...

Beretta F92 Silencer

1911 9mm Ejector

During removal of the lanyard loop spring pin, be sure the punch is left in place to prevent accidental loss of parts or injury to personnel. Ensure hammer is in the down or forward position. 9. With a 1 8 inch punch, drive out the lanyard loop spring pin 1 leaving the punch in place. Place the lanyard loop 2 on a soft support and push down firmly on the top of the receiver to overcome the main spring 3 tension . While maintaining downward pressure, remove the punch and slowly release pressure...

Parts Of A Semi-automatic Pistol

Before starting an inspection, andior performing any maintenance procedures, be sure to clear the weapon. Do not squeeze the trigger until the pistol has been cleared, inspect the chamber to be sure it is empty, and check to see that there are no obstructions in the barrel. Do not keep live amunition near work maintenance area. GENERAL Inspect all assemblies for missing, broken, or loose parts. Inspect parts for cracks, dents, burrs, excessive wear, rust or corrosion. Make sure all items are...

Beretta 92fs Cutaway

Beretta 92f Locking Block Cracks

Make certain weapon is clear and there are no obstructions in the barrel or chamber. Equipment Condition Pistol, field stripped 1. Place barrel assembly 1 on a soft surface. With a 1116 inch punch, lightly tap out locking block plunger spring pin 2 . H 2. Remove locking block plunger 13 from rear of barrel Remove dirt and corrosion from powder-toulded parts with wiping rag dampened with CLP. If necessary, use RBC with bore brush to clean bore and chamber Lightly oil with CLP LSA. 1. Inspect...

Beretta 92f 9mm Semi-automatic Pistol

9mm Firing Bloc

Make certain weapon is clear and there are no obstructions in the barrel or chamber. Equipment Condition Pistol, field stripped The rear sight may be removed without disassembly of the slide. The safety must be in the safe Idownl position. See step 12. 1. Place slide assembly 1 on left or right side with safety ever 2 over edge of soft support. With a 1 16 inch punch, lightly tap out firing pin block spring Firing pin btock is under spring tension. When removing the punch, maintain slight...