Cleaning Suggestions

Your Cynergy Over and Under Shotgun will function better and more reliably over a longer period of time if it is properly maintained and kept clean. BEFORE PERFORMING ANY CLEANING PROCEDURES, ALWAYS MAKE CERTAIN THERE ARE NO SHELLS IN THE CHAMBERS. You should clean your Cynergy after every day of shooting, and more often if it becomes excessively dirty. A minimum cleaning includes wiping down the action and oiling greasing key parts. Most regular maintenance will also include cleaning the...

Operation Of The Safety

The complete action both barrels is put on safe by sliding the thumb safety selector rearward Figure 2 . In the on safe position an S appears directly in front of the safety selector. The above applies whether the selector is positioned for the O over barrel or U under barrel to fire first. To put the gun off safe the safety selector is moved forward Figure 2A . Whenever you are not Safety in the on sale position, with barrel Safety in the off safe position, with barrel selector on over barrel....

Changing Recoil Pads And Adjusting Comb

BEFORE changing any recoil pads or combs, ALWAYS MAKE CERTAIN THERE ARE NO SHELLS IN THE CHAMBERS. Make certain the safety-is in the on safe position. Follow all safety guidelines mentioned in this manual. You can easily make exact length of pull and comb adjustments to your Cynergy shotgun to fit your shooting style. These features aid in comfortable shooting and quicker target acquisition for better scores. Using a spacer with any of the recoil pads allows you to adjust the length of pull...

Changing The Length Of Pull

With the trigger shoe loosely on the trigger plate, select the length of pull by lining up the notch on the right side of the trigger shoe with one of the three notches on the right side of the trigger plate Figure 16 . Make sure you line up the notches so you do not mar the trigger plate. Use an Allen wrench to tighten the screw on the trigger. Be certain the trigger shoe is secure before firing, and periodically check the shoe for any looseness as part of your cleaning and general maintenance...

Changing The Comb And Comb Height

The adjustable comb is available only on Cynergy Composite stock models. These models come with a neutral comb no cast on or off , and is in the center or neutral position. Two optional combs with cast on or off are available from your Browning dealer. They completely replace your present comb, and are adjustable in height as well. To replace the comb, simply tap out the pin with a ' punch or drift pin, from either side Figure 13 . Slide the comb forward off the ribs and off the stock. The new...

Changing Recoil Pads

All Cynergy models are fit from the factory with the standard pad, which provides a 14H length of pull. There is a H difference in the Locate the entry holes in the end of the recoil pad. Start the screws through the pad into the holes in the stock shown with spacer . Locate the entry holes in the end of the recoil pad. Start the screws through the pad into the holes in the stock shown with spacer . thickness of each pad, and each spacer is thick. Call the Parts Dept. number above for ordering...

Assembly

Browning Cynergy Ejector Timing

1 BEFORE USING, CLEAN ANTI-RUST COMPOUND FROM ALL METAL PARTS, paying close attention to the barrel interior and the breech area. The various exposed metal parts of your new Browning Cynergy Shotgun are coated with a rust preventative compound for protection. Browning Oil is especially suited to remove this compound and give your new gun its first lubrication however, any quality gun oil may be used. A heavy oil or grease is recommended to lubricate the ejector cams on both sides of the...

Invector Tube Selection

Back Bored

To help you choose the correct choke tube for each hunting and shooting situation, all Browning Invector choke tubes are inscribed on the side with the patterns they produce with both lead and steel shot. Each Invector tube also has notches in the top rim of the tube. These notches are a code to allow you to determine the choke designation while the tube is installed. Rim notches refer specifically to lead shot. You will need to use the chart below to cross-reference from lead to steel, and...

Removing The Trigger

BEFORE YOU BEGIN TO REMOVE THE TRIGGER, OPEN THE ACTION TO ENSURE THAT THERE ARE NO ROUNDS IN EITHER CHAMBER. All Cynergy Sporting models are supplied with three different styles of trigger shoes. To remove the trigger shoe, loosen the center screw with a u Allen wrench Figure 15 . Loosen the screw so that the trigger shoe slides easily on the trigger plate. Keep the screw threaded at least one thread into the trigger plate so the screw is not lost. Slide the trigger shoe forward to the end of...

Cleaning Procedures

1 BE CERTAIN YOUR GUN'S CHAMBERS ARE UNLOADED. ALWAYS WEAR PROTECTIVE SAFETY GLASSES DURING ALL ASSEMBLY, DISASSEMBLY AND CLEANING PROCEDURES. KEEP AMMUNITION AWAY FROM THE CLEANING AREA. DO NOT TEST THE FUNCTION OF YOUR FIREARM WITH LIVE AMMUNITION. 2 Remove the barrels and forearm from the receiver as explained previously. 3 Using a shotgun cleaning rod with a tip and patch large enough for a snug fit in the bores, insert the rod and lightly oiled patch in the breech end of the barrels and...

Service Or Repair

If your firearm should require service or repairs, we suggest you first contact a local recommended Browning Firearms Service Center. Contact your Browning sporting goods dealer or call our Service Department for the address of the Service Center nearest you. Otherwise, you may send your firearm directly to our own Service Department. For technical questions about your firearm or service, contact Browning Service Department One Browning Place Arnold, MO 63010-9406 Phone 1-800-322-4626 Browning...

The Browning Triple Trigger System

This information will explain how to remove, to replace and to adjust the trigger shoes in the Triple Trigger System, unique to Browning Sporting models. The Triple Trigger System has three different gold finished trigger shoes with different surfaces wide with checkered surface, wide with smooth surface and narrow with smooth surface. Each trigger shoe is adjustable to three positions for length of pull. Please heed all safety warnings, cautions and procedures found in this manual.