Parts List Recoilless Trap Shotgun

When ordering parts please indicate the model name, serial number, stock style, and exterior finish. Do not order parts using key numbers.

KEY NO.

PART NO.

DESCRIPTION

KEY NO.

PART NO.

DESCRIPTION

01

P940001

Action Buffer

52

P940180

Inner Receiver Link

02

P940003

Assembly Key

53

P940183

Inner Receiver Link Retaining Pin

03

P940005

Assembly Key & Trigger Guard Screw

54

P208234

Middle Sight Ivory Color

04

P940008

Assembly Wrench

55

P940186

O-Ring

05

P940011

Barrel Brackel Center

57

P940194

Place Nut "A*

06

P94CÖ14

Barrel Brackel Center Screw

58

P941194

Place Nut "B

07

P940016

Barrel Brackel From

59

P940197

Place Screw

08

P94C018

Barrel Brackel Pin

60

P940200

Receiver Back

10

P94C034

Boil

61

P940204

Recoil Buffer

11

P940037

Boil Assembly Screw

62

P940206

Recoil Pad Assy-

12

P940040

Be*! Handle

63

P940208

Rib Adjusting Screw

13

P940Ö44

8ci1 Slide

64

P940210

Rib Front 30" STD

14

P940049

Butt Pad Retainer

64

P940214

Rib Front 27' MICRO

15

P940052

Butt Pad Retainer Pin

65

P940217

Rib Insert

16

P940055

Butt Pad Retainer Spring

66

P940220

Rib Pivot Plug

17

P940058

Butt Pad Shoe-

67

P940223

Rib Pivot Socket

18

P940062

Butt Pad Shoe Screw Long

68

P940226

Rib Rear

19

P940065

8utt Pad Shoe Screw Short

69

P940230

Sear Assy. Pin

20

P940068

Butt Pad Spacer

70

P940232

Sear Assy. Pin Retaining Pin

21

P940074

Butt Stock Std,

71

P940235

Sear Link

21

P940078

Butt Stock Micro

72

P940238

Sear Link Pin

22

P940082

Butt Stock Bolt Long

73

P940240

Sear Link Pivot Pin

23

P940084

Butt Stock Bolt Short

74

P940242

Sear Link Pivot Pin Ret. Pin

24

P940087

Butt Stock Bolt Lock Washer

75

P940245

Sear Over Travel Adj Screw

25

P940090

Butt Stock Bolt Washer

76

P940248

Sear Pivot

26

P940094

Cocking Lever

77

P940252

Sear Spring

27

P940097

Cccking Lever Hinge Assy.

78

P940256

Sliding Sear

28

P940102

Cocking Lever Pin

79

P940258

Sliding Sear Spring

29

P940105

Delent Spring

80

P940262

Striker

30

P940108

Deiem spring Pin

81

P940265

Striker Assy. Pin

31

P940110

Drive Spring

82

P940268

Striker Rebound Spring

32

P940112

Drive Spring Follower

83

P940272

Striker Sear

33

P940115

Drive Spring Follower Pin

84

P940275

Striker Sear Latch

34

P940118

Drive Spring Tube

85

P940278

Striker Sear Spring

35

P940121

Drive Spring Tube Plug

86

P940280

Stnker Spring Inner

36

P940124

Drive Spring Tube Plug Pin

87

P940282

Striker Spring Outer

37

P940128

Ejeclor

88

P940286

Trigger

38

P940131

Ejector Pin

89

P940290

Trigger Connector

39

P940134

Extractor

90

P940293

Trigger Conneclor Pin

40

P940138

Extractor Pin

91

P940296

Trigger Conneclor Spring

41

P940140

Extractor Spring

92

P940300

Trigger Guard

42

P940144

Forearm

93

P940304

Trigger Pin

43

P940151

Forearm Latch Plate Assy.

94

P940308

Trigger Slide

44

P940157

Forearm Latch Spring

95

P940311

Trigger Slide Pin

45

P940160

Forearm Assy. Mounting Screw

96

P940314

Trigger Slide Spring

46

P208180

Front Sight, White Ivory Color

47

P940164

Inner Receiver Lalch

48

P940168

Inner Receiver Latch Pin

49

P940170

Inner Receiver Lalch Release

50

P940174

Inner Receiver Lalch Release Pin

51

P940177

Inner Receiver Lalch Spring

How Make Rib Barrel

The drop measurement is determined by measuring the distance between the plane formed by the top of the rib and the top of the cheek piece itself (See Figure 9).

BEFORE PERFORMING ANY ADJUSTMENTS, ALWAYS MAKE CERTAIN THERE IS NO SHELL IN THE CHAMBER.

The stock on the Recoilless can be pivoted up or down to adjust drop.

1 Remove the recoil pad by inserting the long end of the alien wrench (supplied with your gun) into the bottom hole on the back of the recoil pad. Push down on the alien wrench to depress the butt pad retainer (See Figure 10). With the butt pad retainer depressed you will be able to slide the recoil pad and butt stock assembly up and off the stock (See Figure ll).

2 Locate the butt stock bolt and loosen (See Figure 12).

3 Pivot the stock either up or down to your desired setting. (See Figure 13). Once you've found a position that gives you a correct sight picture, tighten the butt stock bolt.

DROP ADJUSTMENTS ARE A MATTER OF TRIAL AND ERROR. ADJUST A LITTLE ATA TIME UNTIL YOU OBTAIN THE DESIRED SIGHT PICTURE.

Parts Shotgun Single Barrel

ad retainer.

Browning Recoilless Trap Shotgun

ad retainer.

Bolt Shotgun Part Drawing Single Barrel

Slide the. recoil pad assembly off the stock.

How Adjust Shotgun Comb

4 Replace the recoil pad by sliding it back onto the stock while depressing the butt pad retainer (See Figure 14). The recoil pad should solidly snap in place.

Adjusting the Recoil Pad—

When properly shouldered, your shotgun should nestle into the pocket of your shoulder. Once you have made adjustments to the drop you may find it necessary to adjust the recoil pad to obtain a perfect fit. The recoil pad on the Recoilless can be set at two different settings in the downward position.

1 Adjust the recoil pad by inserting the long end of the alien wrench (supplied with your gun) into the bottom hole on the back of the recoil pad. Push down on the alien wrench to depress the butt pad retainer.

2 With the butt pad retainer depressed, slide the recoil pad downward until the butt pad retainer catches the next setting (See Figure 15).

3 To move the recoil pad to the lowest setting, insert the alien wrench in the middle hole in the recoil pad and depress the butt pad retainer.

Slide the recoil pad until it catches (See Figure 16).

Adjusting Length of Pull—

The length of pull is the distance from the front of the gun's trigger to the center of the butt stock. A length of pull that is too short puts the shooter's face too far up on the stock. A length of pull that is too long forces the shooter to mount the gun on the edge of their shoulder or arm. Length of pull on the Recoilless is adjusted through the use of four interchangeable spacers. Each spacer is 1/4" in thickness. Length of pull for the Micro Recoilless can Ix1 set at 13", 13 1/4", 13 1/2" and 13 3/4". Length of pull for the Standard Recoilless can l)e set at 14", 14 1/4", 14 1/2" and 14 3/4".

1 Remove the recoil pad by inserting the long end of the alien wrench into the bottom hole on the back of the recoil pad. Push down on the alien wrench to depress the butt pad retainer and slide the recoil pad up and off the stock.

2 Remove the two butt pad shoe screws (See Figure 17) and remove the butt pad shoe.

How Remove Shoe From Butt

Keep the butt pad retainer depressed to replace recoil pad.

Browning Recoilless Trap Shotgun

Figure 15

MRSM

Browning Recoilless Trap Shotgun

Increase the length of pull by adding interchangeable spacers.

Increase the length of pull by adding interchangeable spacers.

Browning Recoilless Trap Shotgun

3 With the butt pad shoe removed, fit a butt pad spacer on the stock (See Figure 18).

4 Replace the butt pad shoe by replacing and tightening the butt pad shoe screws and sliding back on the recoil pad.

5 If length of pull is still too short, repeat steps 1 and 2: removing the recoil pad and butt pad shoe. Stack another butt pad spacer onto the last rels only (.745" + 0 - .005), and are not interchangeable with standard 12 gauge Invector choke tul>es. Do not use Invector Plus tubes in barrels threaded for Standard Invector tubes. Do not use Standard Invector tubes in barrels threaded for Invector Plus tubes. Failure to follow these warnings may cause damage to your gun and cause injury to yourself and others.

DO NOT FIRE THIS SHOTGUN WITHOUT HA VING AN INVECTOR CHOKE TUBE INSTALLED.

spacer (See Figure 19) and replace the butt pad shoe and recoil pad. Repeat the procedure again if necessary.

ADJUSTING THE LENGTH OF PULL CAN BE A MATTER OF TRIAL AND ERROR.

Was this article helpful?

0 0

Responses

Post a comment