Troubleshooting Causes And Remedies

If your firearm is properly used and maintained, malfunctions will rarely occur. However, if such a situation does occur please observe the following instructions.

CAUTION - if a malfunction occurs, the possibility of an unintentional discharge is substantially increased. For this reason, when clearing malfunctions, observe the Safety Instructions already mentioned above. Keep the rifle pointed in a safe direction, do not turn the rifle against your body or anyone else's. Do not place your hands in front of the barrel!

Malfunction

Possible Cause

Remedy

A round has not been fed into the chamber.

Magazine is not fully inserted or is damaged. The rifle or cartridges are fouled (dirty).

Insert magazine properly or change magazine. Clean the rifle and cartridges and wipe them dry or as the case may be slightly lubricate.

Firing Pin hole fouled (dirty) or improper lubrication agent used during low temperatures conditions.

Follow the Safety Instructions according to point 20. Disassemble and clean the firing pin or use low temperature lubricant.

A shot sounds "weak".

The primer has been activated but no powder load was inside the cartridge case.

Unload the rifle and check that the bullet is not lodged in the barrel. Any subsequent shot could cause damage to the barrel!

The spent case has not been ejected.

Cartridge chamber, extractor or ammunition dirty or unsuitable lubricant in low temperature environment

Clean and wipe the rifle dry or eventually lubricate lightly with a suitable agent. Use clean and new ammunition.

If you cannot clear away any malfunction in the manner described above, entrust the rifle to a competent gunsmith for inspection and repair.

ILLUSTRATION AND LIST OF PARTS

Magazine Spring 550

1 Barrel

2 Rear Sight

3 Front Sight

4 Front Sight Base

5 Front Sight Base Screw 05

6 Front Sight Base Screw 03

7 Rear Sight Base Screw

8 Front Sight Detent

9 Detent Spring

10 Pin, Front Sight Detent

11 Front Sight Cover

12 Receiver

13 Bolt

14 Bolt Handle Knob

15 Extractor

16 Extractor Collar

17 Firing Pin

18 Firing Pin Spring

19 Support, Firing Pin Spring

20 Nut, Firing Pin Spring

21 Cocking Piece

22 Pin, Firing Pin Nut

23 Cap

24 Bolt Sleeve

25 Disassy Catch

26 Disassy Catch Spring

27 Disassy Catch Pin

28 Disassy Catch Plunger

29 Plunger Spring

30 Plunger Pin

31 Safety

32 Safety Pawl

33 Safety Pawl Spring

34 Roller

35 Safety Pawl Pin

36 Sear

37 Sear Stop

38 Sear Spring

39 Sear Pin

40 Bolt Stop

41 Bolt Stop Spring

42 Safety Pin

43 Retaining Plate

44 Ejector

45 Ejector Pin

46 Ejector Spring

47 Ball

48 Trigger Housing

49 Trigger

50 Trigger Lever

51 Trigger Lever Pin 52-

53 Adjusting Screw, Set Trigger

54 Set Trigger Lever

55 Spring, Set Trigger Lever

- INSTRUCTION MANUAL

56 Pin

57 Retaining Ring

58 Adjusting Screw (B)

59 Spring, Trigger Pull

60 Adjusting Screw, Trigger Pull (A)

61 Locking Nut

62 Adjusting Screw, Trigger Overtravel (C)

63 Locking Nut

64 Nylon Pin (2x)

65 Trigger Mechanism

66 Screw

67 Spring Washer

68 Stock

69 Butt Plate Spacer

70 Butt Plate

71 Screw, Butt Plate

72 Butt Plate Plug

73 Swivel Wood Screw

74 Sling Swivel

75 Swivel Screw

76 Swivel Screw Washer

77 Swivel Assembly

78 Trigger Guard - Box Version

79 Box Shell

80 Floor Plate

81 Floor Plate Pin

82 Floor Plate Latch

83 Spring, Floor Plate Latch

84 Pin, Floor Plate Latch

85 Magazine Box Spring

86 Magazine Follower

87 Front Spacer

88 Frame Screw, Front

89 Rear Spacer

90 Frame Screw, Rear

106 Trigger Spring

107 Stay

108 Reinforcer Screw *

109 Spring Washer*

110 Washer*

111 Reinforcer Nut *

112 Rear Sight Base

113 Rear Sight Blade 200m

114 Rear Sight Blade 300m

115 Rear Sight Spring

116 Rear Sight Spring Screw

117 Rear Sight Blade Pin

118 Locking Screw

* Medium 2x, Magnum 1x

TECHNICAL SPECIFICATIONS

Model

Medium

Magnum

Version

Standard Lux

FS

Safari

Calibers

7 mm Rem. Mag. 300 Win. Mag. 9,3 x 62 *

9,3 x 62

7 mm Rem. Mag. 300 Win. Mag. 9,3 x 62 *

7 mm Rem. Mag. 300 Win. Mag. 375 H&H Mag. 416 Rem. Mag. 416 Rigby 458 Win. Mag.

Overall Length

[mm]

1135

1055

1095 (1055*)

1180

Barrel Length

[mm]

600

520

560 (520*)

635

Sights Radius (Mechanical Sights)

[mm]

420

340

380 (340*)

495

Weight (Empty Magazine)

[kg]

3,3

3,1

3,2 (3,1*)

4,2

Magazine Box, Capacity

[cartridges]

3 (5*)

5

3 (5*)

3 - 5

Trigger Pull, Adjustment Range

[N]

12 -22

12 -22

12 -22

12 -22

+1 0

Post a comment