Table of Contents

Contents 4

How the Super 1050 Works: Stations 1 - 8 5

Super 1050 Assembly 6

Powder Measure Adjustment 8

Primer Magazine 9

Electric Casefeeder 10

Review: How the Super 1050 Works: Stations 1 - 8 10

To Begin Reloading 10

Adjustments 12

Primer Seating Depth - Station 4 11

Casefeeder 12

Handle 12

Swager 12

Swage Conversion & Adjustment 12

Primer System Change Over Instructions 13

Toolhead Removal 14

Shellplate Removal 15

Casefeed Plunger Conversion 15

Die Adjustments 15

Sizing/Decapping Die - Station 2 15

Back-up Expander Die & Swager - Station 3 16

Powder Die - Station 5 16

Bullet Seating Die - Station 7 17 - 18

Crimp Die - Station 8 18

RL 1050 vs. Super 1050 19

Trouble Shooting 20

Maintenance 21

Lubrication Points 22 - 23

Caliber Conversion Charts 24 - 25

Parts List 26

Schematics 27 - 31

#11011 Spot Manuals Super 1050 manual folder SUPER 1050 Manual v1.1 9/01 WJC

Warranty Agreement

The Dillon Super 1050 reloader has been designed as a commercial machine. Our expectation is that its life expectancy will be in excess of two million rounds of loaded ammunition. All Super 1050 machines are warranted for life from defects in material or workmanship, plus a one-year, 100% warranty against normal wear. All electrical/electronic components in Dillon equipment are covered by a one-year warranty.

Mandatory Safety Measures

The reloading of ammunition and the handling of components (gun powder and primers) is inherently dangerous, indeed shooting firearms is inherently dangerous. Accidents can and do occur, sometimes with disastrous results including, but not limited to, loss of vision, hearing or life. These accidents are nondiscriminatory, they occur with both the novice and the experienced reloader.

Dillon Precision Products has consciously designed the Super 1050 with this in mind. We've shielded the primer magazine and machined clearance holes for the elimination of powder and primer residue. In short, we have done everything we know how, to make the use of our machine as safe as possible. We cannot however, guarantee your complete safety. In order to minimize your risk, use common sense when reloading and follow these basic rules:

Never operate the machine without ear and eye protection on. Call our customer service department at (800) 223-4570 for information on the wide variety of shooting/safety glasses and hearing protection that Dillon has to offer.

• PAY ATTENTION: Load only when you can give your complete attention to the loading process. Don't watch television or try to carry on a conversation and load at the same time. Watch the automatic systems operate and make sure they are functioning properly. If you are interrupted or must leave and come back to your loading, always inspect the cases at every station to insure that the proper operations have been accomplished.

• SMOKING: Do not smoke while reloading or allow anyone else to smoke in your reloading area. Do not allow open flames in reloading area.

• SAFETY DEVICES: Do not remove any safety devices from your machine or modify your machine in any way.

• LEAD WARNING: Be sure to have proper ventilation while handling lead components or when shooting lead bullets. Lead is known to cause birth defects, other reproductive harm and cancer. Wash your hands thoroughly after handling anything made of lead.

• LOADS AND LENGTHS: Avoid maximum loads and pressures at all times. Use only recommended loads from manuals and information supplied by reliable component manufacturers and suppliers. Since Dillon Precision has no control over the components which may be used on their equipment, no responsibility is implied or assumed for results obtained through the use of any such components.

Seat bullets as close to maximum cartridge length as possible. Under some conditions, seating bullets excessively deep can raise pressures to unsafe levels. Refer to a reliable loading manual for overall length (OAL).

• QUALITY CHECKS: Every 50-100 rounds, perform periodic quality control checks on the ammunition being produced. Check the amount of powder being dropped and primer supply.

• RELOADING AREA: Keep your components safely stored. Clear your work area of loose powder, primers and other flammables before loading.

• COMPONENTS: Never have more than one type of powder in your reloading area at a time. The risk of a mix-up is too great. Keep powder containers closed.

Be sure to inspect brass prior to reloading for flaws, cracks, splits or defects. Throw these cases away.

Keep components and ammunition out of reach of children.

• BLACK POWDER: Do not use black powder or black powder substitutes in any Dillon powder measure. Loading black powder cartridges requires specialized loading equipment and techniques. Failure to do so can result in severe injury or death.

• PRIMERS: Never force primers. If they get stuck in the operation of the machine, disassemble it and gently remove the obstruction.

Never attempt to clear primers that are stuck in either the primer pickup tube or the primer magazine tube. Never, under any circumstances, insert any type of rod to attempt to force stuck primers out of these tubes. Trying to force primers out of the tube will cause the primers to explode causing serious injury or even death.

If primers get stuck in a primer magazine or pickup tube flood the tube with a penetrating oil (WD-40), throw the tube in the garbage and call us for a free replacement.

Never attempt to deprime live primers - eventually one will go off. When it does it will detonate the others in the spent primer cup. Depriming live primers is the single most dangerous thing you can do in reloading and can cause grave injury or death.

• LOADED AMMUNITION: Properly label all of your loaded ammunition (Date, Type of Bullet, Primer, Powder, Powder Charge, etc.).

• BE PATIENT: Our loading equipment is conservatively rated and you should have no trouble achieving the published rates with a smooth, steady hand. If something doesn't seem right, stop, look and listen. If the problem or the solution isn't obvious, call us. The reloading bench is no place to get into a hurry.

We have done everything we know how to make your machine as safe as possible. We cannot, however, guarantee your complete safety. To minimize your risk, use common sense when reloading and follow these basic rules.

• REMEMBER: If your machine does not perform to your expectations, or if you are having technical difficulties, give us a call. Technical Support (800) 223-4570

Was this article helpful?

0 0

Post a comment