Procedure for immediate action

Operation 1. Remove the magazine.

Operation 2. Pull the cocking handle fully to the rear so that a defective or wrongly positioned round can be cleared from the mechanism.

Operation 3. Release the cocking handle to allow the mechanism to move forward.

Operation 4. Replace the magazine.

Operation 5. Recock the weapon then release the cocking handle, so that a new round is fed into the chamber.

Operation 6. Resume firing

If the stoppage recurs, find out the cause.

3. Stoppages

Regular cleaning and correct maintenance will ensure that stoppages with this rifle are very rare. Their chief cause is insufficient gas, which may be due to Incorrect setting of the gas regulator, fouling of piston head or gas plug, or some obstruction fouling the mechanism.

STG58C GUNSMITHING SERVICES

Call: (626)962-8712 / Fax: (626) 962-4692 http://www.entreprise.com

□ TUNE-UP PACKAGE - 1) Throat Erosion - inspect barrel erosion. 2) Clean & lubricate all parts. 3) Headspacing - inspect & correct headspace to military specifications. 4) Check barrel for alignment & proper torque. 5) Gas Piston - inspect for abnormal wear. 6) Gas System - inspect for leakage & clean gas block. 7) Bolt assembly - clean & inspect extractor. 8) Inspect & clean firing pin and spring. 9) Lap bolt carrier to receiver. 10) Clean recoil spring {lower receiver must be sporter)

□ ACTION JOB - 1) Inspect & adjust for 8 lb. let off. 2) Inspect & adjust trigger spring. 3) Inspect & adjust plunger spring. 4) Inspect & adjust trigger assembly. 5) Inspect & adjust sear. 6) Deburr & polish all contact points 7) Polish hammer & sear pin. 8) Polish trigger face.

□ METRIC TO INCH CONVERSION - Remill the following: 1) Cocking handle rail - to accept folding cocking lever. 2) Magazine well - to accept inch magazine. 3) Modify dustcover. 4) Mill cocking handle slot on receiver

□ REBLUE ENTIRE WEAPON - sand blasting & complete disassembly included

□ PARKERIZE ENTIRE WEAPON - sand blasting & complete disassembly included

□ INSTALL U.S. COMPONENT PARTS KIT (parts kit not included)

□ MODIFY MAGAZINE WELL to accept inch magazine

□ MODIFY RECEIVER for inch pattern cocking handle

□ NATIONAL MATCH HEADSPACING (locking shoulder not included)

□ HEAT TREAT UPPER RECEIVER

□ CUSTOM SERIAL NUMBER

□ INSTALL SKELETONIZED STOCK

□ MACHINE RECEIVER FOR CARRY HANDLE SLOT

□ SAFETY INSPECTION

□ RETAP METRIC RECEIVER OR ISRAELI BARREL

□ LAP BOLT CARRIER TO RECEIVER

□ MATCH TARGET CROWN 1t°(for chrome lined add $20)

□ INSPECT / REPAIR EXTRACTOR for proper ejection; smooth & polish extractor surface

□ REPAIR GAS LEAK (front end) - seal gas tube to gas block

□ INSTALL MUZZLE BREAK - on threaded barrel or non-threaded barrel

□ WELD ON MUZZLE BREAK - does not included refinishing

□ TIGHTEN & ACCURIZE REAR SIGHT - eliminate horizontal & vertical play between receiver surfaces

□ REPAIR & ADJUST TRIGGER PULL - adjust trigger spring, plunger spring & trigger assembly

□ BOLT & CARRIER INTERFACE - smooth & polish surfaces; deburr & polish all internal surfaces D ACCURIZE UPPER & LOWER RECEIVER - maintain ZERO play between upper & lower receiver fit

□ ACCURIZE BOLT & LOCKING SHOULDER - assure full bolt & shoulder contact

□ CARBINE CONVERSION - for chrome lined barrels add $20: 1) Cut boitel to legal minimum 2) Recrown

ULTRA HEAVY DUTY STEEL RINGS -MED #TT700RING

ULTRA HEAVY DUTY STEEL RINGS - HIGH #TT700RIHI

MULTI-PURPOSE FRONT SIGHT ADJUSTMENT TOOL #Q1-FRTSGT

FAL DUSTCOVER #TT3

FAL DUSTCOVER #TT3

STEEL FAL HAMMER #IUS1

STEEL FAL SEAR #IUS2

FAL CHROME LINED GAS PISTON #IUS3

STEEL ZEROCLIMB MUZZLE BREAK #IUS4

MAGAZINE BASE-PLATE #IUS5

EXTENDED FAL

GAS ADJUSTMENT TOOL

#Q1-GASTL

MAGAZINE FOLLOWER #IUS6

BUnSTOCK REMOVAL TOOL #Q1-GASTL

BUnSTOCK REMOVAL TOOL #Q1-GASTL

CARRYING CASE

SLING #SSARCB7

#SSARSB

Call: (625)962-8712 / Fax: (626) 962-4692 http //www.entreprise.com

STG58C MODELS Police GgaJUm ™-4adli|

Scout Qa/dUnc

Ga/dUtie

PoliCA ^GSUfßt

Was this article helpful?

0 0

Post a comment