Madsen 1947 Bolt

Homemade M16 Front Sight Tool

Parts Legend

1. Barrel 2.. Front sight

3. Front sight cover

4. Rear sight

5. Rear sight blank

6. Receiver

7. Cartridge stop

8. Cartridge stop screw

9. Cartridge guide

10. Cartridge guide screw

11. Cartridge guide screw bushing

12. Spring cover base

13. Spring cover leaf

14. Spring cover base screw

15. Spring cover leaf pin

16. Spring cover spring

17. Spring cover stop pin

18. Upper tang screw

19. Breechbolt

20. Ejector

21. Ejector spring

22. Ejector collar

23. Finger lever connecting pin

24. Extractor

25. Extractor pin

26. Firing pin

27. Firing pin stop pin

28. Hammer

29. Hammer screw bushing

30. Hammer screw

31. Hammer spring guide rod

32. Hammer spring guide rod pin

33. Hammer spring

34. Hammer spring abutment

35. Hammer spring abutment pin

36. Lower tang

37. Trigger

38. Trigger pin

39. Trigger spring

40. Finger lever

41. Friction stud

42. Friction stud spring

43. Friction stud stop pin

44. Locking bolt, right

45. Locking bolt, left

46. Finger lever bushing pin

47. Finger lever bushing

48. Carrier

49. Carrier plunger

50. Carrier plunger spring

51. Carrier plunger pin

52. Magazine tube

53. Magazine spring

54. Magazine follower

55. Magazine plug

56. Magazine plug screw

57. Forearm tip

58. Forearm tip screws (2)

59. Forearm tip tenon

60. Buttplate

61. Buttplate screws (2) Note: Stock and forearm not shown

Glisenti 1886

The Winchester Model 71 lever-action rifle was first announced in January 1936. Of solid-frame construction, the Model 71 was essentially a revamped version of the famous Browning-designed Model 1886 rifle.

The rimmed .348 Winchester cartridge, designed especially for the Model 71, was offered in 150-, 200-, and 250-gr. loadings to give a range of power adequate for virtually all American big game: No other commercial rifle was chambered for this cartridge.

The Model 71 was initially furnished with both 20" and 24" barrels, but the 20"-barrel model was discontinued in 1947. The deluxe model was stocked in selected walnut and both pistol grip and fore-end were checkered. The pistol grip was capped with hard rubber. Quick-detachable swivels with 1" leather sling were standard.

The lower-priced standard model had a plain stock, with no swivels or sling. Deluxe and standard models were available with aperture or open rear sights.

The Model 71 was discontinued in 1958.

Disassembly Procedure

Lower lever (40) and check action to be sure rifle is unloaded.

To disassemble magazine assembly, unscrew magazine plug screw (56) and remove plug (55), withdrawing magazine spring (53) and follower (54) at same time. Remove forearm tip screws (58) and slide forearm tip (57) up on magazine tube slightly. Using a punch or similar tool through magazine plug screw holes at front end of magazine tube, unscrew tube from receiver. Remove magazine tube and forearm from receiver.

To disassemble action, remove upper tang screw (18) and pull buttstock off receiver to rear. Buttstock may require sharp rap with the hand to loosen it. Remove spring cover base screw (14) and lift spring cover assembly (parts 12, 13, 15, 16. and 17) up out of receiver. Drift out hammer spring abutment pin (35), taking care not to allow abutment to escape under tension of hammer spring. Remove hammer spring abutment (34) and lift small

Madsen 1947 Bolt

1 After removing magazine plug screw (56), magazine plug (55). spring (53), and follower (54), unscrew magazine tube (52) as shown, using a punch or similar tool through the plug screw holes at front end of magazine tube

Samuel Colt Finger Lever Rifle Picture

2 When reassembling breechbolt (19). finger lever (40). and carrier (48), the parts should be replaced in receiver as shown. When replacing finger-lever connecting pin (23) through bolt and top of finger lever, be sure ejector (20) is pushed as far back into bolt as possible spring (39) out top of trigger (37). Remove hammer screw (30) and hammer screw bushing (29) and lift hammer (28) with hammer spring (33) and guide rod (31) out top of receiver. Lower tang (36) may be knocked out bottom of receiver to rear. Drift out finger lever bushing pin (•46) from left to right and remove finger lever bushing (47). Note that finger lever bushing pin is a slotted pin and should not be mistaken for a screw. Remove right and left locking bolts (44 and 45) from bottom of receiver. Lower finger lever, moving breechbolt back out of receiver until finger-lever connecting pin (23) is exposed. Drift out pin (23) with a punch and remove breechbolt (19) to rear, taking care not to allow ejector (20). spring (21). or collar (22) to escape. Drop finger lever (40) and carrier (48) out bottom of receiver. Remove cartridge guide screw (10) and bushing (II) from right side of receiver and drop cartridge guide (9) out of receiver. Remove cartridge stop screw (8) from left side of receiver and drop cartridge stop (7) out of receiver.

Reassemble in reverse order. Install breechbolt and finger lever, carrier, and locking bolts before attempting to replace cartridge guide. Cartridge guide can be replaced through spring cover hole in right side of receiver with rear end of cartridge guide in place in right locking bolt. ■

Hunting Mastery Selected Tips

Hunting Mastery Selected Tips

Deer hunting is an interesting thing that reminds you of those golden old ages of 19th centuries, where a handsome hunk well equipped with all hunting material rides on horse searching for his target animal either for the purpose of displaying his masculine powers or for enticing and wooing his lady love.

Get My Free Ebook


Responses

  • semrawit
    How to assemble a winchester model 150?
    7 years ago
  • lionella
    How to assemble and disassemble lever action rifle?
    6 years ago

Post a comment