Cocking the pistol

Cocking Desert Eagle

Never chamber a round unless you are ready to fire. 2. Insert the magazine. The magazine will have about 1 16 inch play when seated properly Do not push up on magazine when firing or jamming will occur. 3. Grasp the slide, pull it all the way back and release it fig. 8 . This operation cocks the hammer and chambers a cartridge. This pistol is now loaded, cocked with the safety catch lever in the SAFE position therefore, make sure that the barrel is pointed in a safe direction. With the...

Assembly of the slide

Desert Eagle Bolt Disassembly

Insert the bolt stabilizer - guide pin first. Make sure that its concave part coincides with the bolt housing in the side. 2. Insert the bolt into its housing in the slide and compress the stabilizer spring with it. 3. Insert the bolt guide pin. fig. 18 . 4. Make sure the safety catch is in the TIRE position. 5. Install the firing pin spring and the firing pin, with its narrow section facing down 6. Insert the firing pin stop semicircle part up. Push the firing pin in with the combination...

Care And Cleaning

Comprehensive knowledge of how to service and handle the pistol is of great importance. Experience has shown that most failures which occur while operating the pistol are due to negligence in maintenance. Special attention must be paid to cleaning, lubricating and inspecting the pistol this will determine whether or not the pistol will function properly when you need it. In order to maintain accuracy, the barrel must be serviced thoroughly. The slide, the bolt and other moving parts of the...

General Characteristics

Desert Eagle Mark Xix Caliber 50ae

A safety catch, operable from either side, blocks the firing pin and at the same time disconnects the trigger from the firing mechanism. The pistol chamber is chrome plated to facilitate easier cartridge case extraction. The polygonal rifling reduces barrel wear and enhances the obduration between the bullet and the bore, thus increasing accuracy. Field stripping is simple since the pistol has only six main parts, including the magazine. The rotating bolt interlocks with the barrel during...

Exploded View

M1911 Trigger Mechanism Diagram

DESERT EAGLE ADJUSTABLE TRIGGER ASSEMBLY Desert Eagle Adjustable Trigger Assembly - includes the following parts Trigger Trigger Pin Trigger Spring Trigger Bar 25 RECOIL SPRING ASSEMBLY - MK I VII .357 00024-1 1 60 RECOIL SPRING ASSEMBLY - MK XIX .357 00025-01 60 - includes the following parts Recoil Spring Outer Recoil Spring Plate Cross piece - MK I VII Recoil Spring Plate Cross piece - MKXIX Recoil Spring Rod - MK I VII Recoil Spring Rod - MK XIX Retaining Ring C-CLIP - MK I VII Retaining...

Sights And Zeroing

The standard sights consist of a rear sight and a front sight. Both are combat type. They are designed to ensure rapid and accurate aiming. The square notch on the rear sight is 3 mm wide. The sight line radius is 210 mm. The existing dovetail slots are designed to accommodate front target type sights and rear adjustable sights, available as an accessory option. Mark XIX,.357, .44, .440 amp .50 The 7 8 rib has cross-slots to allow installation of Weaver style rings. The existing 3 8 dovetail...

Assembly Magnum Mark I VII

Spring Assembly Desert

Insert recoil spring assembly into frame from its front end, open end first with the sharp corner of the spring plate down rounded forward edge of spring plate up fig. 1 5a . Now push the recoil spring assembly fully home into its recesses in the frame. It is important to have the spring plate in the proper position. 2. Mount the slide onto the frame and draw it to the rear. 3. Hold the slide back against slight spring tension and place the barrel lock lug in the slide recess. 4. Push...

Disassembly And Assembly

Desert Eagle Draw Parts

This chapter deals with those disassembling operations and assembling operations which the user should carry out for routine maintenance of the pistol. Disassembling or assembling of any other parts is not recommended and will void all warranties. IT IS POSSIBLE TO ASSEMBLE THE SAFETY CYLINDER IN A BACKWARD REVERSE ORDER. IF THIS HAPPENS, THE SAFETY AND FIRE FUNCTION INDICATORS WILL ALSO BE REVERSED. THE GUN WILL THEN FIRE WHEN ON SAFE. DO NOT DISASSEMBLE THE SAFETY. FOR SERVICE ON SAFETY...

Disassembly of the trigger mechanism assembly

Magnum Trigger Meganism

Lean the frame on the hammer and horn. Push the grip pin in with the combination tool through the small hole in the bottom of the grip and push the grip cover downward to release it fig. 20 . 2. With both thumbs on the projection at the top of the butt, pull the front edges of the grip backward to remove it from the butt fig. 21 . 3. Remove the hammer pin and the sear pin with the appropriate punch fig. 22 . 4. Lift the trigger mechanism assembly from the frame.