Step Control

1. Glue the rubber or plastic strip to the other 1-1/2" x k" strip of wood. This will be the bottom of the box. When assembling, the plastic or rubber will be facing up.

2. Screw the hinges to one of the 2-1/2" x V pieces of wood and attach the other side of the hinge to the side of one of the 2-1/2" x J-l/2" pieces of wood.

3. Drill a >/l6" bole in the bottom of the other 2-1/2" x 1-1/2" piece of wood, which will be the left side of the box, and a 1/8" hole in the top right hand corner of the other 2-1/2»» x V piece of wood, which will be the back wall of the box.

4. Using nails, screws or glue, assemble the box. There will be no top to it.

If you decide to build a bigger switchboard, It would be a good 1-dca to keep the control buttons In groups of 3 for easy hookup, repair, and replacement of batteries.Be sure to label each button so you can i-dentify it with your target. If you plan to hook up your defenses a-gainst a future attack, you should protcct the wires running from the control box to the mines. Either coat them with a spray or paint to avoid deter¡oration of the insulation, or encase the wires in tubes like BX cable.

Besides the switchboard hookup for manual detonation, flashbulbs are great for all sorts of contact mines. trip wires, and bombs to combat tree climbing snipers.

6. From Fig. 5, connect wire 0 to wire D on the control box and then connect wires A, B, & C to wires A, 8, & C from the control box. See Fig. 6 for completed assembly.

coiled bare wire resting on rubber

POOR MAWS JAMES BOND Vole 2 38

THE POOR MAN'S ARMORER

Improvised Claymore Mine

By Raymond J. Lamer

Black Powder Squib:

Obtain a 12 volt lamp bulb (with a flange on it [head or tail light bulbj). Carefully break the glass off of the bulb. Solder wire leads to the rear and the side of the bulb. You can check the filament by very quickly attaching the wire leads to a 12 volt battery. Glue the bulb into the rear of the claymore casing with the flange inside the case and the wire leads out the back] Hake a paper cylinder that is large enough and long enough to protect the filament of the bulb. Glue this cylinder to the inside of the casing so that it protects the filament.

Cas ing:

This can be made of almost anything, but 1/8 inch thick plexiglass is one of the easiest materials to work with. Make a small box that is 3 Inches wide by 6 Inches long by 1 inch deep. You need k sides and a bottom but no top. Use solvent type glue to put the box together.

Note: the box can be made any size. The larger it Is the wore damage you can do with it but also the more explosive it will take to fill it.

Drill a hole in the middle of the bottom of the casing large e-nough to put the base of the light bulb thru. Install the black powder squib in the casing as shown in the drawings.

Cast!ng:

Make a motd with an outside length and width slightly less than the inside dimensions of the casing. This should be approx. I .inch deep. This rroId can be made with body putty or with plaster of paris.Let it cure and then use spray paint to coat the inside of it until the mold is smooth to the touch.

To Cast:

Spray the inside of the mold with a casting release agent. Mix and pour liquid casting plastic into the mold until it Is approx. l/k inch deep. Now pour in 3/16'• or \/hu steel ball bearings until you have a' layer of them covering the bottom of the mold. Add casting plastic if needed so that the layer of balls is barely covered. Set the mold a-slde and let the plastic cure, NOTE: Plaster of Paris or body putty can also be used to cast the balls in. The ball bearings are the easiest to work with but'any metal can be used (nuts, bolts, screws, nails, etc.).

When the cast i ng has cured, remove it from the mold. Use alcohol to remove the wax residue from the casting.

Now carefully pour black powder into the paper cylinder that protects the filament of the bulb in the casing. Lightly shake the casing to settle and pack the black powder around the filament. Now fill the rest of the casing with black powder until you have a level layer of black powder slightly a-bove the top of the paper cylinder.

Place the casting inside the casing on top of the layer of black powder. Now use a sillcorve or plastic sealing compound to seal around the k edges of the casting. Once It drles your claymore mine Is ready to be used. NOTE: for concealment use colored plexiglass or paint the claymore after you've put it toget-. ber.

Emplacement:

To place the claymore, tape It to a tree, pole or what ever is handy. Make Sure the ball bearings point toward the enemy. Remember that this type of weapon produces a mean back blast so make sure you are under cover when you set It off.

You can make up a control board to control a number of claymores that you have in place. Or you can simply string wires from each of your mines to a central location

Was this article helpful?

0 0

Post a comment