Maintenance Of Sling And Snap Hook Assembly

This task covers:

Disassembly/lnspection/Repair/Reassembly

INITIAL SETUP

MOS 76Y Supply Clerk\Unit Armorer MOS 211 lnfantry Weapon Repairer (USMC)

References

TM 9-1005-201-10

TM 08671A-10/1A

Equipment Condition

Sling and Snap Hook Assembly removed.

DISASSEMBLY/INSPECTION/REPAIR/REASSEMBLY

DISASSEMBLY/INSPECTION/REPAIR/REASSEMBLY

1. Remove ends of Sling, Small Arms (1) from Buckles (2).

2. Remove two Snap Hooks (3) from Sling, Small Arms (1).

3. Visually inspect Sling, Small Arms (1) for torn webbing or stitches and two Buckles (2) for bends or breaks. Replace Sling, Small Arms (1) if unserviceable.

Torn Web Sling
2 ) (3

4. Visually inspect two Hooks (5) for bends or breaks and inspect two Snaps (4) for spring tension. Replace Snap Hook (3) if unserviceable.

5. Put two Buckles (2) on Sling, Small Arms (1) ends; put two Snap Hooks (3) on Sling, Small Arms (1) and run ends of Sling, Small Arms (1) through Buckles (2) to secure.

Section VI. INSTALLATION AND MAINTENANCE OF ADAPTER ASSEMBLY

FOR M122 TRIPOD MOUNT.

2-23. INSTALLATION OF ADAPTER ASSEMBLY.

This task covers:

Installation

INITIAL SETUP

Tools and Special Tools

References

Tool Kit, Small Arms Repairman

TM 9-1005-201-10

SC 5180-95-CL-A07

TM 08671A-10/1A

Tool Kit, Small Arms Repairman

TM 9-1005-224-10

USMC TAM No. E2900

TM 02075E-10/1

TM 9-1005-224-24

TM 9-1005-224-24P

Personnel Required

TM 02075E-24&P/2

MOS 76Y Supply Clerk/Unit Armorer

MOS 2111 Infantry Weapon Repairer

Equipment Condition

(USMC)

Traversing and Elevating

Mechanism Assembly (T&E)

removed from M122 Tripod Mount.

INSTALLATION

NOTE

a. To install M249 Adapter Assembly, it is necessary to disassemble the M60 adapter components from the T&E mechanism.

b. It is not necessary to remove both Retaining Rings (1) from Retaining Pin (2).

1. Remove one Retaining Ring (1) from either end of Retaining Pin (2) and remove Retaining Pin (2) from T&E Mechanism (3).

2. Separate M60 Adapter (4), Spring (5) and Plunger (6) from T&E Mechanism (3).

NOTE

M60 Adapter (4), Spring (5) and Plunger (6) are integral components of M122 Tripod Mount, therefore should not be discarded when removed.

Tripod Adaptor Assembly Army

2-23. INSTALLATION OF ADAPTER ASSEMBLY (Cont)

INSTALLATION (Cont)

3. Install M249 Adapter (7) by inserting Forked End (8) of adapter onto Traversing Shaft (9).

4. Aline M249 Adapter (7) with T&E Mechanism (3) holes. Insert Pin (2) and Snap Retaining Ring (1) in notch of Pin (2).

NOTE

For maintenance of T&E Mechanism (3) refer to TM 9-1005-245-13&P.

1005 245 13p
2-24. MAINTENANCE OF ADAPTER ASSEMBLY FOR M142.

This task covers:

Disassembly/Inspection/Repair/Reassembly

INITIAL SETUP

Tools and Special Tools

References

Tool Kit, Small Arms Repairman 1

I TM 9-1005-245-13&P

SC 5180-95-CL-A07 1

1

Tool Kit, Small Arms Repairman

Equipment Condition

USMC TAM No. E2900

1 M142 Adapter Assembly removed from

| Mount.

Personnel Required

MOS 76Y Supply Clerk/Unit Armorer

MOS 2111 Infantry Weapon Repairer

(USMC)

1095 197 7902

Was this article helpful?

0 0

Responses

  • lemlem teodros
    How to put a sling on for m249?
    8 years ago

Post a comment