Headquarters Department Of The Army

AUGUST 1985

Instructions ManualHeadquarters Department The Army

WARNING

Make sure that each weapon is unloaded prior to inspection.

Avoid having live ammunition in the vicinity of the work area.

Dry cleaning solvent is flammable and toxic and should be used In a well-ventilated area. The use of rubber gloves is necessary to protect the skin when cleaning revolver parts.

Avoid skin contact with carbon removing compounds.

Beware of obstructions in the barrel. Inspect the barrel for obstructions before firing. Objects in the barrel such as mud, snow, twigs, or heavy amounts of CLP can cause obstructions resulting in a bulged or burst barrel. If, when firing, a weak or peculiar report is heard, stop firing at once to inspect the barrel for a stuck bullet.

SAFETY PRECAUTIONS (General)

The following general safety precautions are also applicable. There are many safety rules, but those found below are basic and should be observed rigidly.

The revolver must always be checked for live ammunition when picked up, drawn from the holster, handed to, or accepted from, another person.

The revolver should always be bolstered except when drawn for a definite purpose. Never point the revolver at anything that you do not Intend to shoot.

Do not cock the revolver unless you intend to shoot it. Do not even insert the finger in the trigger guard until you are ready to fire.

Dry-snapping, even with dymmy cartridges, should be discouraged unless it is performed on a regular target range or at a known target.

When the revolver is out of the holster and held in a ready position, be absolutely certain that it is not pointing at any part of yourself or at other persons who are near you.

V FIRST AID

For additional first aid data, see FM 21-11. AMMUNITION

TM 9-1300-206 provides information for revolver ammunition.

TECHNICAL MANUAL ) HEADQUARTERS

\ DEPARTMENT OF THE ARMY

No. 9-1005-206-14&P-1 ) Washington, DC 28 August 1985

Operator's, Organizational, Direct Support, and

General Support Maintenance Manual Including Repair Parts And Special Tools List for

REVOLVER, CALIBER .38 SPECIAL: SMITH AND WESSON, MILITARY AND POLICE, M10

ROUND BUTT, 4-INCH BARREL (1005-00-937-5839)

ROUND BUTT, 2-INCH BARREL (1005-00-937-5840)

SQUARE BUTT, 4-INCH BARREL (1005-00-214-0934)

REVOLVER, CALIBER .38 SPECIAL: RUGER SERVICE SIX, 4-INCH BARREL, M108

SQUARE BUTT, W/O LANYARD LOOP <1005-01-040-8969)

SQUARE BUTT, W/LANYARD LOOP (1005-01-040-8990)

ROUND BUTT, W/LANYARD LOOP (1005-01-094-7045)

Current as of 29 January 1985 for Appendix C.

REPORTING ERRORS AND RECOMMENDING IMPROVEMENTS

You can help improve this manual. If you find any mistakes or if you know of a way to improve the procedures, please let us know. Mail your letter. DA Form 2028 (Recommended Changes to Publications and Blank Forms), or DA Form 2028.-2 located in the ba$k of this manual direct to: Commander, US Army Armament, Munitions and Chemical Command, ATTN: AMSMC-MAS, Rock Island, IL 61299-6000. A reply will be furnished to you.

'This manual supersedes TM 9-1005-206-14P/1, dated 22 February 1971.

lllut Pftflê Ftgur«

CHAPTER 1 INTRODUCTION 1-1

Section I General Information 1-1

Section II Equipment Description 1-1

Section III Technical Principles of Operation 1-4

CHAPTER 2 OPERATING INSTRUCTIONS 2-1

Section I Description and Use of Operator's Controls and Indicators 2-1

Section II Operator/Crew Preventive Maintenance Checks and Services (PMCS) ... 2-2

Section III Operation Under Usual Conditions 2-6

Section IV Operation Under Unusual Conditions 2-8

CHAPTER 3 OPERATOR MAINTENANCE INSTRUCTIONS 3-1

Section I Lubrication Instructions 3-1

Section II Troubleshooting 3-3

Section III Operator Maintenance Procedures 3-3

CHAPTER 4 AMMUNITION 4-1

CHAPTER 5 ORGANIZATIONAL MAINTENANCE INSTRUCTIONS 6-1

Section I Repair Parts, Special Tools, TMDE, and Support Equipment 5-1

Section II Service Upon Receipt 5-1

Section III Organizational Preventive Maintenance Checks and Services (PMCS) 5-2

Section IV Troubleshooting 5-5

Section V Organizational Maintenance Procedures 5-6

Section VI preparation for Storage or Shipment 5-8

CHAPTER 6 DIRECT AND GENERAL SUPPORT MAINTENANCE INSTRUCTIONS 6-1

Section I Repair Parts, Special Tools, TMDE, and Support Equipment 6-1

Section II Service Upon Receipt 6-1

Section III Troubleshooting 6-1

Section IV Direct and General Support Maintenance Procedures 6-6

Section V imbrication 6-53

Section VI Preparation for Storage or Shipment 6-53

Section VII Preembarkatlon Inspection of Materiel In Units Alerted for Overseas

APPENDIX A REFERENCES A-1

APPENDIX B MAINTENANCE ALLOCATION CHART B-1

APPENDIX C ORGANIZATIONAL, DIRECT SUPPORT AND GENERAL SUPPORT

MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LIST C-1

Section I Introduction C-1

Section II Repair Parts List CM

Group 00 Revolver assembly (Smith and Wesson) C1-1 C1

Group 01 Barrel assembly (Smith and Wesson) C2-1 C2

Group 02 Receiver assembly (Smith and Wesson) C3-1 C3

0202 Cylinder and yoke assembly (Smith and Wesson) C4-1 C4

0203 Hammer assembly (Smith and Wesson) C5-1 C5

0204 Rebound slide assembly (Smith and Wesson) C6-1 C6

0205 Trigger assembly (Smith and Wesson) C7-1 C7

0206 Frame assembly (Smith and Wesson) C8-1 C0

Group 00 Revolver assembly (Ruger) C9-1 C9

Group 01 Barrel assembly (Ruger) C10-1 C10

Group 02 Receiver assembly (Ruger) C11-1 C11

0201 Strut assembly (Ruger) C12-1 C12

0202 Cylinder and crane assembly (Ruger) C13-1 C13

0203 Hammer assembly (Ruger) C14-1 C14

0205 Trigger assembly (Ruger) C15-1 C15

0206 Frame assembly (Ruger) C16-1 C16

Section IV National Stock Number and Part Number Index 1-1

APPENDIX D ADDITIONAL AUTHORIZATION LIST D-1

APPENDIX E EXPENDABLE/DURABLE SUPPLIES AND MATERIALS UST E-1

APPENDIX F ILLUSTRATED LIST OF MANUFACTURED ITEMS F-1

ALPHA3ETICAL INDEX Index 1

TM 9-1005-206-14&P-1

Caliber Ruger Inch Barrel
(1) revolver, caliber .38 special: s and w, military and police, m10, round butt, 4-inch barrel (1005-00-937-5839)

(4) revolver, caliber .38 special: ruqer service six, 4-inch barrel, m108, square butt w/0 lanyard loop (1005-01-040-8989)

Caliber Ruger Inch Barrel

(2) revolver, caliber .38 special: s and w, military and police, m10. round butt, 2-inch barrel (1005-00-&7-5840)

Calibre GunPistols Tattoo

(5) revolver, caliber .38 special: ruger service six, 4-inch barrel. m108. square butt w/lanyard loop (1005-01-040-8990)

Caliber Revolver Parts Drawing

(3) revolver, caliber .38 special: s and w, military and police, m10. square butt, 4-inch barrel (1005-00-214-0934)

(6) revolver, caliber .38 special: ruqer service six, 4-inch barrel, m108, round butt w/lanyard loop (1005-01-094-7045)

Full External Views of .38 Caliber Revolvers.

Was this article helpful?

0 0

Post a comment