Volt

Lamp Module Model L60 1.47 inch Diameter Bezel

Lithium Batteries Model SF123A

Lamp Module Model L60 1.47 inch Diameter Bezel

Adapter Lamp Module Model L36 Model A12 1.47 inch Diameter Bezel

Adapter Lamp Module Model L36 Model A12 1.47 inch Diameter Bezel

Adapter

Model A12 Lamp Module Model KT1*

2.5 inch TurboHead Bezel

Adapter

Model A12 Lamp Module Model KT1*

2.5 inch TurboHead Bezel

All lamp modules accept either a standard output lamp assembly or an ultra-high intensity lamp assembly. Run time for the standard lumen output is approximately 60 minutes and the high intensity lumen output time is 20 minutes per battery set.

B5 Lumen

Standard Lamp Assembly Model PB0

120 Lumen

Ultra-High Intensity Lamp Assembly

Model P61

B5 Lumen

Standard Lamp Assembly

Model N1

B5 Lumen

Standard Lamp Assembly Model PB0

120 Lumen

Ultra-High Intensity Lamp Assembly

Model P61

B5 Lumen

Standard Lamp Assembly

Model N1

9 Volt

Lamp Module Model LM90 1.625 inch Diameter Bezel

Lamp Module Model LM90 1.625 inch Diameter Bezel

Lamp Module Model L90 1.47 inch Diameter Bezel

Lamp Module Model L90 1.47 inch Diameter Bezel

Adapter

Model A12

Adapter

Model A12

Lamp Module Model L39 1.47 inch Diameter Bezel

Adapter

Model A12

Adapter

Model A12

Lamp Module Model L39 1.47 inch Diameter Bezel

Three Lithium Batteries Model SF123A

Adapter

Model A12

Adapter

Model A12

Adapter

Model A12

Adapter

Model A12

125 Lumen

Standard Lamp Assembly Model MN10 225 Lumen

Ultra-High Intensity Lamp Assembly Model MN11

105 Lumen

Standard Lamp Assembly Model P90

200 Lumen

Ultra-High Intensity Lamp Assembly

Model P91

200 Lumen

Ultra-High Intensity Lamp Assembly

Model P91

105 Lumen

Standard Lamp Assembly

Model N2

Lamp Module Model KT2* 2.5 inch TurboHead Bezel

105 Lumen

Standard Lamp Assembly

Model N2

*The prefocused beam of the 2.5" TurboHead on the Model KT1 and Model KT2 Lamp Modules is more concentrated than the beam with the 1.47" bezel. The intensified beam center illuminates greater distances.

6 Volt Laser

Lithium Batteries Model SF123A

Laser Sight

Adapter

Model A12

Lithium Batteries Model SF123A

Adapter

Model A12

Model L72 Red Model L80 Green Model L75 Infrared

5 Milliwatt Output NOTE

Constant-on switches are not available for use with laser sights by Federal Regulations. Please select a pressure-type switch for use with a laser sight.

STEP 4 Select Your Switch

1. Decide how you would like to control your light:

* Constant-On only

* Constant-On and Momentary-On

* Momentary-On with the ability to disable the switch

* Momentary-On only

2. Refer to the chart below for the various options offered.

3. Select the type of switch: tail-cap, rocker or tape.

4. If tape switch cables are required to reach areas of the weapon for placing pressure switches, measure the length of cable(s) required.

5. Derive your Model Number, replacing the xx and/or yy in the selected switch model number with the required cable length in inches.

Constant-On Only

Constant-On and Momentary-On

Tail-Cap

Rocker

Tail-Cap Switches

Tape Switches

Switch location on light module

On/Off Flag Switch

Push Button 1st Step - Momentary 2nd Step - Constant

On/Off Flag Switch

On/Off Tailcap Flag Switch

Model U00T

Waterproof to 30 meters

Model U00TH

Switch location position on forend or pistol grip

On/Off Switch

Replace the xx in the model number with the length of the switch cable needed to reach from the light module to the desired location for the On/Off Switch.

Model UxxB

Waterproof to 30 meters

Model UxxBH

Switch location on light module

Note: The SW02 and Z41 also have the disable feature

*The standard Pressure Switch pad is 2.25 inches long. A Pressure Switch pad 5 inches long is available. To order the switch with the longer pressure pad add the letter "L' at the end of the model number. (Example - U05TKL)

Push Button 1st Step - Momentary 2nd Step - Constant

Tailcap Two-Step Push Button Switch

Rotate CW Constant

Push Button Press - Momentary

SWO2

Rotate CW Constant

Push Button Press - Momentary

Tai Push-Sw cap

Button tch

Flag Switch Constant On

Pressure Switch Press - Momentary

On/Off Switch

Pressure Switch Press - Momentary

Model Z41

Waterproof to 30 meters

Model SW02H

Waterproof to 30 meters

Model Z41H

plus

plus

A21 Adapter

A21 Adapter

Tailcap Switch must be used with the

A21 Adapter to mount the switch on the lamp module

Tailcap Switch must be used with the A21 Adapter to mount the switch on the lamp module

Constant-on Switch positioned on the Light Module and Momentary-On/Off Switch positioned on the weapon

Flag Switch Constant On

Pressure Switch Press - Momentary

Pressure Switch* and

On/Off Flag Switch

Replace the xx in the model number with the length of the Pressure Switch cable needed to reach from the light position to the desired location for the Pressure Switch.

Model UxxT

Waterproof to 30 meters

Model UxxTH

Waterproof to 30 meters with stiffened Pressure Switch

Model UxxTK

Switch locations on forend and pistol grip

Pressure Switch Press - Momentary

On/Off Switch

Pressure Switch* and On/Off Switch

Replace the xx in the model number with the length of the Pressure Switch cable needed to reach from the mount position to the desired location for the Pressure Switch and replace the yy with length for the On/Off switch.

Model UxxyyB

Waterproof to 30 meters

Model UxxyyBH

Waterproof to 30 meters with stiffened Pressure Switch

Model UxxyyBK

0 0

Post a comment